Controllable driver chip
LPD6803, LPD8806, LPD1882, LPD1889, LPD6812, LPD1883, LPD1886, DMX512, HDMX, APA102, MY9221, UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, UCS8904, WS2801, WS2803, WS2811, WS2812, TM1803, TM1804, TM1809, TM1812, TM1829, TA9912, TM1913, TM1914, TM1926, TM1814, INK1003, LX1003, LX2003, LX2006, TLS3001, P9813, P9816, SM16711, SM16716, LD151x, LD153x, MBI6021, MBI6023, MBI6024 like.




 LED Device Type must be set in the computer software while driving chip share option program in the computer displays only one


property in the name of the representative.
Note: The controller controls up to 2048 pixels means that the controller can output data 2048 points, while the actual signal can reliably transmitted to the end, will depend on the performance of luminaires, switching power supply EMI, overall interference project site.


Features
1, an output port to control up to 2048 pixels.
2, SD card support FAT32, FAT16 format, the maximum capacity of 32G bytes and above. Allows up to 32 DAT files, playback order is file names in alphabetical order.
3, using a mobile phone switch file, adjust the speed and brightness settings unicast or full broadcast like.
4, using a mobile phone output text, pictures or graffiti.
5, two tranches of voltage input, DC5V or DC9-24V.
6, through the button to switch files, adjust playback speed, set the full multicast or unicast.


Button operation
Stop button after three seconds, automatically save the parameters.
1, "ALL / SINGLE": full multicast / unicast switching, the green indicator light when the whole broadcast, unicast green light off.
2, "FILE": switch to the next DAT file. If the current is the last file you jump to the first file.



3, "SPEED-" and "SPEED +": set the playback speed, maximum speed is 100, the minimum speed is 1, except for one, the other multiples are 5 such as: 5,10,15,20,25 ....
4, "ALL / SINGLE" + "SPEED +": first press the "ALL / SINGLE" hold, then press "SPEED +", WIFI connection routers and name itself restore the default values. Router default connection is "LED168", password is "88888888", its name is in the back was kind enough to have six characters at the beginning of XXX, password is "88888888."


Normal Operating Instructions
1, you must first insert the SD card, after power.
2, SD card for the first time, or more deleted needs to be formatted to FAT32 or FAT16 format. Full support SD4, SD6, SD10, the maximum of 32G bytes or more. SD memory card allows up to 32 DAT files are sorted in alphabetical playback controller based on the file name.
3, an output port to control up to 2048 pixels. 2304 actual control point, just a 48X48 dot matrix screen.


4, in the "LED preparation software" setting, select a line a sub-controller (in this case a controller), the controller type selection SB, choose a good driver chip type and clock, in-line driver chip clock is generally 0.8M, double line driver chip clock can be set to 1.5MHz, 0.75MHz and 0.37MHz.
5, the playback speed, file selection and full multicast / anycast mode settings using the keys on the controller.
6, more than 256 gray-driver chips, Gamma process has been made on the controller. Such as: LPD6812, MBI6021 to 1024 gray, LPD1886, TLS3001 for the 4096 gray, MBI6024, UCS8904, MY9221, LD151x, LD153x to 65,535 gray.
6. LD1510, LD1512, LD1530, LD1532 only supports 8 and 16 mode.


Mobile phone operating instructions
1, start the mobile phone software "ask us in email", the main interface displays DAT file name and icon, and Controller inserted corresponding to the file on the SD card.
2, check WIFI connection, ignore this step if you have connected well. Click "Menu" - "WLAN Set", then pop WLAN settings interface. Note Do not use the phone a static IP, because IP settings or may not lead to communication errors. To "WLAN" and "Auto Access" tick, the phone will automatically scan at WLAN network will see to the rear at the beginning was kind enough to have a network name XXX six characters. Select it to enter the password "88888888" and click the "Connect" button. Wait a moment the phone will connect successfully, the status bar at the top of the phone will add a WIFI icon. Press the Return key to exit the WLAN settings.



If the phone is connected on controller, finger click on the icon to switch files.
3, click "Menu" - "Settings", pop-up settings dialog box, you can adjust the speed and brightness by sliders. Select "Single file playback", loop the same file. To replace DAT file icon, click the button "Select DAT file icon", bring up the file selection interface, find and select the icon file, return to the main interface will find the icon has changed, as shown below.


Icon file format image (jpg, png, bmp, etc.), size should not be too wide, preferably not more than 160 high, all in the same folder. Filename naming provisions: _ prefix number prefix must be the same, numbers do not add 0 before. The correct name, such as: A_1.PNG, A_2.PNG, A_3.PNG, ......, A_9.PNG, A_10.PNG, A_11.PNG. It corresponds to the order number and a DAT file, if not a number, the default icon is displayed.
To export text, pictures or graffiti, as shown in the following figure needs "Width" and "Height" input screen width and height, alignment now provides the line from the lower left, vertical folded, if found wrong color RGB, under Graphs "RGB order" select RGB order.


Click "Menu" - "Doodle", enter the graphic output and graffiti interface. The upper part of the box for the graphic output and graffiti area, here is the color selection bar, and then enter the following text size, starting location and text, click the "Send" text output to the upper box. Click "Open" selectable output image.


Settings and restore the router and names
The phone can be connected to controller, then controlleris hot, the phone is a terminal; controllercan also be connected to the router, then the router is hot, controlleris terminal. That controllercan make hot, but also at the same time as the terminal.
controllerdefault router connected to "XXX", password is "88888888", its name is back at the beginning of XXX kind enough to have six characters, the password is "88888888."
To modify click "Menu" - "Config", first select the router Controller will be connected, and enter the connection password of the router. If you do not want to change the router, select the last item "Not set", do not enter the password.


In the "Name of controller" Enter the new name, and enter a new password (the password is empty means open), if the "Name of controller" does not change the name or leave it blank. Click to return to the changes. To cancel the modification, click "Cancel".
Password Forgot your controller, you can connect it via a router connected to the controller. If the router connected to it have forgotten, by combining key recovery "ALL / SINGLE" + "SPEED +": first press the "ALL / SINGLE" hold, then press "SPEED +".


The controller interface definitions
Single wire connected to the drive control IC GND, DAT
Control wire connected to GND, CLK, DAT driving IC
DMX512 control when connected to GND, D-, D +



Specifications
Input voltage DC5V or DV9-24V
Power 0.3W
Load points 2048 points
Weight 0.1Kg
Operating temperature -20C ° --75C °
Dimensions L150 x W82 x H38



Package Contents.:


1X LED Wifi controller including Cable Connector and Antenna

>Software download <




Write a review

Note: HTML is not translated!
    Bad           Good

LED Wifi/TEXT Controller WS2812b Madrix WS2811/Lpd6803/

  • Product Code: 0004
  • Availability: In Stock
  • $49.50


Related Products

16*16  LED Panel WS2812B RGB LED Full Color Digital Flexible Display Board 5V 256 Pixels

16*16 LED Panel WS2812B RGB LED Full Color Digital Flexible Display Board 5V 256 Pixels

16*16 WS2812B WS2812b 5050 SMD RGB Flexible LED Pixel Panel Light DC5VDescription:This large 16*16..

$49.50

400W 80A 5V Single Output AC/DC Switching Power Supply Ultra Slim

400W 80A 5V Single Output AC/DC Switching Power Supply Ultra Slim

400W 80A 5V Single Output AC/DC Switching Power Supply Ultra Slim Weight:670g21.5*11.6*2.6 cmInput V..

$43.99

WS2812B/SK6812 Flexible Rollable LED Panel 1000X1000mm 3600LED´s Individual Addressable LED SFTC Function

WS2812B/SK6812 Flexible Rollable LED Panel 1000X1000mm 3600LED´s Individual Addressable LED SFTC Function

WS2812B/SK6812 Flexible Rollable LED Panel 1000X1000mm 3600LED´s Individual Addressable LED SFTC Fun..

$285.00

WS2812b WS2811 LED Strip 5050 RGB LED strip Light Waterproof Individually Addressable DC5V 30/60/144LED Meter

WS2812b WS2811 LED Strip 5050 RGB LED strip Light Waterproof Individually Addressable DC5V 30/60/144LED Meter

WS2812b WS2811 LED Strip 5050 RGB LED strip Light Waterproof Individually Addressable DC5V 30/60/144..

$34.99

Tags: LED Wifi Controller, WS2812b, PLD6803